|
|
|
| - or - |
 |
 |
1-800-456-9012
Catalog & Samples |
 |
|
|
|
| |
|
|
|
THE
EXCLUSIVE IMPORTER OF
 |
|
|
| WE PROVIDE CUSTOMERS
WITH CABLE MANAGEMENT SOLUTIONS! |
|
|
| -Quantity Discounts! |
-No Minimum
Orders! |
-Same
Day Shipping! |
| -Blanket Orders! |
-Quick and Friendly Service! |
-All Major Credit Cards! |
| |
|
|
|
| TECHNICAL
INFORMATION - PRODUCT SPECIFICATIONS |
|
| |
|
| |
NYLON |
Pressure
rating:
150 PSIG (10 BAR) NEMA 4x, 6 (Submersible) & 12
- IP 68 / IP 69 K |
Materials:
Fittings: Nylon 6/6, V0: Flame resistant,
halogen - and phosphor free, self extinguishing,
non-toxic
O-Ring & Seal
Ring: Buna-N/Polyethylene
(Viton® optional) |
[Applies
to pages: 5, 6, 7, 8, 9, 10 & 11] |
|
|
OPERATING
TEMPERATURE |
| EXPOSURE |
STATIC |
DYNAMIC |
CONTINUOUS
(NYLON & NICKEL
PLATED BRASS) |
-40°F
to 212°F
(-40°C
to 100°C) |
-4°F
to 176°F
(-20°C
to 80°C) |
| SHORT
TERM |
248°F
(120°C) |
212°F
(100°C) |
|
NICKEL
PLATED BRASS |
Pressure
rating:
150 PSIG (10 BAR) NEMA 4x, 6 (Submersible) & 12
- IP 68 |
Materials:
Body, Dome
Nut: Nickel Plated Brass
Spring (Flex
extension): Stainless
Steel
Splined Bushing & Form
Seal: Nylon 6/6, V0: Flame resistant, halogen
- and phosphor free, self extinguishing,
non-toxic
O-Ring & Seal Ring: Buna-N/Polyethylene
(Viton® optional) |
[Applies
to pages: 10, 11, 14, 15 & 16] |
|
|
Selection
Criteria For Strain Relief Fittings:
-
Cable
OD (Outside Diameter)
-
Threads
type & size
-
Nylon,
Brass, PVDF, or Stainless Steel
-
Nut
and/or O-Ring/Seal Ring
|
|
 |
Viton® is
a federally registered trademark of DuPont Dow
Elastomer.
|
THREAD
SPECIFICATIONS (PITCH & MAJOR DIA.)
|
NPT THREAD
SPECIFICATIONS |
THREAD
SIZE |
1/4" NPT |
3/8" NPT |
1/2" NPT |
3/4" NPT |
1" NPT |
1-1/4" NPT |
1-1/2" NPT |
2" NPT |
Major Dia. Inches (mm) |
.54
(13.72) |
.69
(17.15) |
.84
(21.34) |
1.05
(26.67) |
1.32
(33.40) |
1.66
(42.16) |
1.90
(48.26) |
2.38
(60.33) |
| Pitch (mm) |
.056"
(1.41) |
.056"
(1.41) |
.071"
(1.81) |
.071"
(1.81) |
.087"
(2.21) |
.087"
(2.21) |
.087"
(2.21) |
.087"
(2.21) |
Threads per Inch |
18 |
18 |
14 |
14 |
11.5 |
11.5 |
11.5 |
11.5 |
PG
THREAD SPECIFICATIONS |
THREAD
SIZE |
PG
7* |
PG
9 |
PG
11 |
PG
13.5** |
PG
16 |
PG
21 |
PG
29 |
PG36 |
PG
42 |
PG48 |
Major Dia. Inches (mm) |
.49"
(12.5) |
.60"
(15.2) |
.73"
(18.6) |
.80"
(20.4) |
.89"
(22.5) |
1.11"
(28.3) |
1.46"
(37.0) |
1.85"
(47.0) |
2.13"
(54.0) |
2.39"
(59.3) |
Pitch (mm) |
.05"
(1.27) |
.055"
(1.41) |
.055"
(1.51) |
.055"
(1.51) |
.055"
(1.51) |
.062"
(1.59) |
.062"
(1.59) |
.062"
(1.59) |
.062"
(1.59) |
.062"
(1.59) |
METRIC
THREAD SPECIFICATIONS |
THREAD
SIZE |
M6 |
M8 |
M12 |
M16 |
M20 |
M25 |
M32 |
M40 |
M50 |
M63 |
Major Dia. Inches (mm) |
.24"
(6) |
.31"
(8) |
.47"
(12) |
.63"
(16) |
.79"
(20) |
.98"
(25) |
1.26"
(32) |
1.57"
(40) |
1.97"
(50) |
2.48"
(63) |
Pitch (mm) |
.04"
(1.0) |
.05"
(1.25) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
.06"
(1.5) |
|
.
* PG 7 thread fits 1/4" NPT or 1/2"-20
UNF.
. **
PG 13.5 is also known as PG 13.
. Taps
are readily available. Call for sources and
more detailed PG thread specifications. |
 |
 |
•
World-wide most commonly used type thread
• Characterized by its major diameter and its pitch
• Designated by the letter M followed by the value of the nominal diameter and the pitch, both expressed in millimetres and separated by the multiplication sign '×' (i.e. M12 x 1.5) |
• NPT Thread = National Pipe Thread
• Taper rate for all NPT threads is 1/16
• The taper on NPT threads allows them to form a seal when torqued as the flanks of the threads compress against each other, as opposed to straight thread fittings |
 |
 |
• PG Thread = Panzer-Gewinde
(also Panzer-Rohr-Gewinde)
• German thread type
• Depth of thread smaller than NPT or Metric, but larger flank angle |
• BSPP Thread = British Standard Pipe Parallel Thread
• Parallel (straight) thread with a constant diameter, denoted by the letter G
• Symmetrical V-thread in which the angle between the flanks is 55°
(measured in an axial plane)
• One-sixth of this sharp V is truncated at the top and the bottom
• Threads are rounded equally at crests and roots by circular arcs ending
tangentially with the flanks
• The theoretical depth of the thread is therefore 0.64 times the nominal pitch |
TORQUE
RECOMMENDATIONS FOR STRAIN RELIEF
FITTINGS
Torque in
inlb (Nm)
|
METAL
STRAIN RELIEF FITTINGS |
PLASTIC
STRAIN RELIEF FITTINGS |
| DOME
NUTS |
THREAD
AND LOCK NUTS |
DOME
NUTS |
THREAD
AND LOCK NUTS |
| PG
7, M12x1.5 |
36.9
(4.17) |
55.3
(6.25) |
14.4
(1.62) |
22.1
(2.50) |
| PG
9, PG 11, M16, PG 13.5, 3/8" NPT,
1/2" NPT, M16x1.5, M20x1.5 |
36.9
(4.17) |
55.3
(6.25) |
22.1
(2.50) |
33.2
(3.75) |
| PG 16,
1/2"NPT-E |
44.2
(5.00) |
66.4
(7.50) |
29.5
(3.33) |
44.2
(5.00) |
| PG 21,
PG 29, PG 36, PG 42, PG 48, 3/4"NPT,
1"NPT, 1-1/4"NPT, 1-1/2"NPT,
M25x1.5, M32x1.5, M40x1.5, M50x1.5, M63x1.5 |
59.0
(6.67) |
88.5
(10.00) |
44.2
(5.00) |
66.4
(7.50) |
|
|
Note: Torque
for dome nuts was determined using a metal rod.
It may vary for cable, depending on the crush
resistance of the cable. We recommend to determine
the actual torque empirically, testing the actual
cable used. The values shown above are for reference
only. |
|
Note: Nylon
strain relief fittings installed in a threaded
connection and exposed to elevated temperature
should be retained with a sealant such as Locktite® to
avoid a loose connection when temperature fluctuates. |
|
|
|
|
 provides
cable products at competitive prices with exemplary customer
service. Inventory in Excess of $25 Million allows the immediate
shipment of almost all standard cable types and sizes. |
 |
Cables,
Wires & Accessories: Domestic & Imported
Exclusive North American importer
of HELUKABEL®. Approvals: RoHS,
UL, CSA, Harmonized & CE. We offer cables for Power, Control,
High/Low Temp., Hi-Flex, Robotic, Track, Servo, VFD, Composite,
Ribbon, Data(CAT), Single Conductor, Etc! |
 |
Plastic
Enclosures: Indoor
/ Outdoor NEMA 4x
Exclusive importer of HENSEL ENCLOSURES.
Industrial Strength, UV & Impact Resistant, Modular
Expandable. Opaque/Transparent covers. Hinged! Exceptional
Value! Accessories: DIN rails, Mounting plates, Terminal
blocks, Hole plugs, Etc. International and Domestic
Approvals. |
 |
Aluminum
Enclosures: Custom
Customize your own Control Solution
Device with the following Cord Grips, Momentary Push Buttons, Etc.
NEMA 4, 4x (IP66) We offer 1, 2 & 3 Button Solutions. Assembly
at one low price. |
 |
Pneumatics: Fittings, Flow Control Valves & Accessories
CAMOZZI Pneumatic Automation Components. Our fittings range includes Nickel Plated Brass & Composite fittings with Metric or NPTF Threads, the patented & longstanding Pro-Fit® system, High Pressure Dual Seal fittings, etc..
The range of Valves includes flow regulators, quick release valves, flow control valves, basic logic functions and silencers with different specifications in order to meet most requirements. |
|
|Strain Relief Fittings & Accessories|Adapter, Enlarger, Reducer|Explosive Proof Fittings|
|Circular
Connectors|Conduit
System|Enclosures|Product Index|Search|Media|
|Site Map|Online
Catalog|Company Overview|Contact|Privacy
Policy| |
|
|
14853 E. Hinsdale Ave.,
Suite D
Centennial, CO 80112-4240 USA
Toll Free: 800-456-9012 / 303-699-1135 Fax: 303-680-5344 |
 |
Top of Page |
|
|
|
Nylon
Fittings 
